Help

GPU tab

Update your graphics driver, clear its cache, and find the optional NVIDIA tuning tools.

On this page

Where: Open TOOLS → GPU.

You do not need to tune your graphics card to use START. The tools shown depend on your card and driver.

Choose the right tool#

You want to…Open
Update your graphics driverGPU Update
Clear saved graphics data when troubleshootingShader Cache
Try an automatically tested NVIDIA undervoltSmart Automatic Undervolt
Adjust NVIDIA voltage and speed by handNVIDIA V/F Curve (advanced)
Check your graphics card for errors under loadStress Test Center

GPU Update#

A driver is the software Windows uses to work with your graphics card. This tool supports NVIDIA and AMD, not Intel graphics.

Before updating

Save your work and close games. Your screens may flicker or go black during installation. Let it finish, then restart Windows if asked.

  1. Click Check for Updates.
  2. Click Manage to review the options.
  3. Choose the installation option for your card.
  4. Follow the prompts.

NVIDIA offers a clean installation. AMD offers Custom Install to choose components, or Open Vendor Page to visit AMD's driver website. Keep components you use, such as sound through HDMI or DisplayPort.

Shader Cache#

This clears saved graphics data. Try it when troubleshooting graphics problems or unusual stutter.

  1. Close your games.
  2. Click Clear Cache.

Games rebuild this data when needed. The next launch may take longer or stutter while that happens.

Smart Automatic Undervolt#

An undervolt tries to run your graphics card at a lower voltage. This optional NVIDIA tool tests a candidate for you. Results vary between cards.

Before testing

Save your work and close games and other GPU tuning tools. The card may get hot and the fans may get loud. Stay nearby while the test runs.

  1. Open Smart Automatic Undervolt.
  2. Read the preparation prompts.
  3. Start the test.
  4. Wait for the result.
  5. Choose Save Profile to keep a validated result, or Discard to reject it.

Nothing is saved until you choose Save Profile. A failed or interrupted test does not save its candidate.

Using a validated profile#

  1. Open TOOLS → Games → View Detected Games.
  2. Click Settings next to your game.
  3. Under GPU, turn on Automatic Undervolt Profile.
  4. Click Save.
  5. Press START when you are ready to play.

STOP removes the applied profile. Turn the game's switch off and save to stop using it in future sessions.

NVIDIA V/F Curve#

Advanced: this editor lets you choose voltage and speed yourself. If you are new to GPU tuning, leave it alone or use Smart Automatic Undervolt above.

Careful

An unsuitable target can crash a game or the graphics driver. Test changes before using them for gaming.

Open the editor#

  1. Finish your START session and any running tests.
  2. On the GPU tab, click Open Manual V/F Curve Editor.

The editor opens separately and TinyBoost minimizes. If MSI Afterburner is running, TinyBoost resets and closes it first. If the button is unavailable, read the message below it.

What you see#

LabelMeaning
ChartVoltage along the bottom; speed up the side
LIVE EST.An estimate of where the card is running
> 1100 mVPoints beyond TinyBoost's supported selection limit
CURRENT / REQUESTEDThe current reading and your chosen target
PROFILE 1 2 3Three places to save a manual profile

An estimated or preview-only chart is not a full reading from your card. What the editor can apply depends on the card and driver.

Make an undervolt#

The graph is a row of dots. Each dot pairs a voltage with a speed:

  • Left and right: voltage, shown in mV. Further left means less voltage.
  • Up and down: speed, shown in MHz. Higher means a faster requested speed.

For an undervolt, you choose a dot and make the graph flat to its right. This asks the card to stop increasing the requested speed at those higher voltage points.

Set the graph step by step#

  1. Choose a PROFILE slot. An occupied slot loads its saved curve.
  2. Find your chosen voltage along the bottom of the graph. Follow it upward to a dot on the curve. Choose a point at or below 1100 mV.
  3. Right-click that dot. The dots to its right form a flat line.
  4. Drag the selected dot up or down to set the speed of that flat line. Up requests more MHz; down requests fewer MHz.
  5. Check REQUESTED. Make sure the voltage and speed match what you intended.
  6. If you made a mistake, click Reset Graph and start again. This reloads the curve last read from your card.
  7. Click Save Target and wait for the saved confirmation.
  8. Click Close Window.

What should the finished graph look like? It rises toward your chosen dot, then continues as a horizontal line to the right. If the right side still rises, right-click your chosen dot again.

There is no single voltage and speed that suits every card. If you do not know which values to choose, use Smart Automatic Undervolt instead of copying another card's settings.

Saving does not apply the profile. A flat curve requests the same speed at higher voltage points; check the card's live readings after applying it.

Other controls:

  • Click empty chart space to leave the highlighted flat-section selection, then drag a point to adjust it alone.
  • Double-click a point, then drag to move the whole curve.
  • Reset Graph returns the chart to the curve last read from your card.

Use it#

  1. Open TOOLS → Games → View Detected Games.
  2. Click Settings next to your game.
  3. Under GPU, turn on Manual VF Undervolt.
  4. Click Save.
  5. Press START to apply it.

The selected manual slot is used. STOP removes the applied profile. During a session, the gear beside STOP opens Running games, where you can change the switch and click Apply.

Only one GPU control can be selected: Manual VF Undervolt, Automatic Undervolt Profile, or Nvidia P0 GPU Clock Lock. Turn clock lock off before choosing an undervolt.

If a profile belongs to a different graphics card, reopen the editor and save a profile for your current card.

Test it#

  1. Open the Stress Test Center.
  2. Choose GPU Stress Test.
  3. Under Test with, select your saved V/F Curve profile.
  4. Start the test.

Current settings does not load a saved profile automatically. If the test reports errors or games crash, stop using the profile and review your tuning.

Remove a profile#

Turn off Manual VF Undervolt in the game's settings to stop using it. Right-click a profile slot to delete its saved target.

Reset All Settings also clears saved profiles, but resets other TinyBoost settings too. See Undoing changes.

When your screen briefly goes black#

Some GPU actions ask to restart the graphics driver. Save your work before accepting. Wait for the screen and TinyBoost to return.

If a tool remains unsupported after updating the official driver, leave that tool off.